Taizhou Huangyan Aoxu Mould Technology Co., Ltd

High quality mold &.product, professional service, being the core supplier in mold manufacturing industry!

Plastic Mold For Dustbin

Plastic Mold For Dustbin

Plastic Mold For Dustbin 1.Specification: Item: Plastic Injection Mold Part Material: HDPE/PE Core &Cavity Steel: P20 Mold Base Steel: S50C Runner: Hot or Cold Gate Type: Sprue Gate/Pin Point Gate/Edge Gate Cavity No: Single Mold Base Standard: DME/LKM/HASCO/Etc. Spare Parts Standard:...

Send InquiryChat Now
Product Details

Plastic Mold For Dustbin


1.Specification:
Item: Plastic Injection Mold
Part Material: HDPE/PE
Core &Cavity Steel: P20
Mold Base Steel: S50C
Runner: Hot or Cold
Gate Type: Sprue Gate/Pin Point Gate/Edge Gate
Cavity No: Single
Mold Base Standard: DME/LKM/HASCO/Etc.
Spare Parts Standard: DME/HASCO/DAIDO/MISUMI/Customized is acceptable.
Mold Life: 30k-1, 000 k
Cycle Time: 80-120 s
Lead Time: 65days
Injection Machine: 1000Ton


2.Mold Image

20180918092603.jpg


3.About Our Service
Aoxu Mould Technology offers more injection molds parts design and manufacturing service, we have more 13+ experience in injection molds field. All of projects we will put them from DFM to PFM working flow to ensure products quality, from molds design, mold flow analysis, per-mold machining review a series of testing reports to make sure mold production running smoothly. We are proud of our mold producing flowing, product quality guarantee, delivery on time and we have professional engineer team to support your projects, make it so easy, make you so comfortable.


4.Plastic Mold Design Guidelines

Size
The maximum part outline that can be molded is approximately 18.9 in. (480mm) by 29.6 in. (751mm) or roughly equivalent to 175 sq. in. (1,129 sq. cm.). A maximum part volume of approximately 59 cu. in. Depth up to 4 in. (101mm) from the parting line with 3 degrees of draft, or up to 8 in. (202mm) total if the parting line can pass through the middle of the part, inside and outside. Deeper parts are limited to a smaller outline.
Draft
A taper applied to the faces of the part that prevent them from being parallel to the motion of the mold opening is called draft. This keeps the part from being damaged due to scraping as the part is ejected out of the mold. Recommended draft:
0.5 degrees on all vertical faces is strongly advised.
2 degrees works very well in most situations.
3 degrees is minimum for a shutoff (metal sliding on metal).
3 degrees is required for light texture (PM-T1).
5 or more degrees is required for heavy texture (PM-T2).
Tolerances
Typically, Proto Labs can maintain a machining tolerance of ±.003 in. (0.08mm) with an included resin tolerance that can be greater than but no less than ±.002 in./in. (0.002mm/mm).
Wall thickness
With injection-molded parts, observing proper (and uniform) wall thickness helps parts avoid potential issues such as sink marks and warpage. Recommended thicknesses vary by material:

ResinInches
ABS0.045 - 0.140
Acetal0.030 - 0.120
Acrylic0.025 - 0.500
Liquid crystal polymer0.030 - 0.120
Long-fiber reinforced plastics0.075 - 1.000
Nylon0.030 - 0.115
Polycarbonate0.040 - 0.150
Polyester0.025 - 0.125
Polyethylene0.030 - 0.200
Polyphenylene sulfide0.020 - 0.180
Polypropylene0.025 - 0.150
Polystyrene0.035 - 0.150
Polyurethane0.080 - 0.750

Surface finish

A number of standard finishes are available for injection-molded parts at Proto Labs. Our current finishes include non-cosmetic, low-cosmetic and EDM finishes; bead-blast texturing; and high-end mold polishing.

Radii

Because Aoxu employs an automated CNC milling process to make the mold for your parts, some part corners will end up with a radius rather than a sharp edge. This does not usually require a change to the model, but the designer is made aware of these radii before the mold is made.

Ejector pins

Aoxu' s injection molding process uses ejector pins of various sizes to push the plastic part out of the mold after it has solidified. The sizes and arrangement of these pins are selected to minimize the impact on your part design. Ejector pins range in size from 0.063 in. (1.6mm) to 0.5 in. (12.7mm), with sizes larger than 0.063 in. (1.6mm) preferred.

Undercuts

Our molding process supports simple undercuts in your part geometry. Maximum side core dimensions:

WidthHeightPull
≤ 8.419 in≤ 2.377 in≤ 2.900 in
≤ 213.84mm≤60.38mm≤73.66mm


5.Product Image

QQ图片20180918094829.png


6.Q/C Inspect Mold

1.Mould Material Q/C

- Mould Steel Checking(Hardness, Crack ,Blow hole material defects )

- Mould Standard Spare Parts Checking(hardness, size, flaw checking)

2. Mould Machining Process Q/C

- Design checking (Part design, mould design,Including 2D drawing and 3D drawing) 

- Each part of mould's size checking after machining according to 2D drawing

- Mold Test (check mould running conditions and T1 samples)

3.Make sure to follow and checking each points of customer's request before shipment.


7.SAMPLE NOTE & SHIPPING PART

Sample Free.  

Mould Guarantee: In Mould Life Period Appeared Mould Issues And If Caused By Our Technical Problems,

We Will Provide The Free-Fixing Service, If Caused By Clients, Can Discuss With Us To Solve The Problems.

Package: Will Use Best Bubble Wrap And Then Wooden Pack For Safe Shipping.

Express Fee & Shipping Fee Need To Paid In Client's Charge.

AFTER-SELL SERVICE: We Accept Any Issues Caused By Us And Will Solve The Problems Actively, Any Issues.  

Are Available To Solve If Our Product Happend Any Quality Issues And Complaints.


8.Mold Packing &. Delivery

QQ图片20180827152920.png


9.Contact us

2.png



Hot Tags: Plastic Mold For Dustbin, Dustbin Mold, Plastic Mold
Related Products
Inquiry