Taizhou Huangyan Aoxu Mould Technology Co., Ltd

High quality mold &.product, professional service, being the core supplier in mold manufacturing industry!

Home > Exhibition > Content
Keywords for injection molds
- Aug 26, 2017 -

入水:gate                                 进入位: gate location                    
水口形式:gate type                    大水口:edge gate 
细水口: pin-point gate               水口大小:gate size                       
转水口: switching runner/gate  唧嘴口径:sprue diameter 
流道: runner     热流道: hot runner,hot manifold                                   
热嘴冷流道: hot sprue/cold runner     热流道板:hot manifold 
唧嘴直流: direct sprue gate               

圆形流道:round(full/half runner                                       
流道电脑分析:mold flow analysis       插头: connector plug 
流道平衡:runner balance                   

热嘴: hot sprue                                                           
发热管:cartridge heater                  

探针: thermocouples                                                      
插座: connector socket                   

密封/封料: seal 
运水:water line                   喉塞:line lpug                 
塑胶管:plastic tube              快速接头:jiffy quick connector plug/socker 
喉管:tube 
三板模:3-plate mold           模具零件:mold components   
二板模:2-plate mold           边司/导套:bushing/guide bushing 
中托边Lguide pin               边钉/导边:leader pin/guide pin     
螺丝: screw                       中托司:shoulder guide bushing   
顶针板:ejector retainner plate    内模管位:core/cavity inter-lock 
托板: support plate           

管钉:dowel pin                                                               
开模槽:ply bar scot             顶针: ejector ping       
司筒针:ejector pin              推板:stripper plate        
斜顶:lifter                          扣机(尼龙拉勾):nylon latch lock
模胚(架): mold base        司筒:ejector sleeve 
缩呵:movable core,return core core puller 
上内模:cavity insert            下内模:core insert   
行位(滑块): slide               耐磨板/油板:wedge wear plate 
镶件:insert                        压座/斜鸡:wedge      
压条:plate                         撑头: support pillar      
唧嘴: sprue bushing           复位键、提前回杆:early return bar
挡板:stop plate                  定位圈:locating ring      
锁扣:latch                         承压平面平衡:parting surface support balance  
扣鸡:parting lock set          斜顶杆:angle ejector rod
推杆:push bar                   不准用镶件: Do not use (core/cavity) insert   
栓打螺丝:S.H.S.B               初步(正式)模图设计:preliinary (final) mold design   
尼龙拉勾:parting locks        模排气:parting line venting 
顶板:eracuretun                回针碰料位:return pin and cavity interference  
活动臂:lever arm               顶针碰运水:water line interferes withejector pin
分流锥:sprue sperader       料位出上/下模:part from cavity (core) side                          
镶针:pin                           用铍铜做镶件: use beryllium copper insert 
水口司:bush                       模总高超出啤机规格:mold base shut hight 
均匀冷却:even cooling        稳定性好:good stability,stable
垃圾钉:stop pin                 弹弓压缩量:spring compressed length          
隔片:buffle                       

强度不够:insufficient rigidity                                               
热膨胀:thero expansion     铜公(电极):copper electrode
弹弓柱:spring rod              中托司:ejector guide bush       
中托边:ejector guide pin    斜顶:angle from pin 
弹弓:die spring                   波子弹弓:ball catch   
喉塞: pipe plug                  

锁模块:lock plate                                                               
销子:dowel pin                 活动臂:lever arm     
斜导边:angle pin               反呵:reverse core 
气阀:valves                      术语:terms 
扣模:sticking                    公差:tolorance
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.